Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5794 visitantes y 
5 usuarios online.
Productos
Información
Destacado
Inicio >> CROSSLEE >> G454ROYALBELM.LFE Manual de Usuario
 
 0 artículo(s) en Su carrito 

CROSSLEE G454ROYALBELM.LFE
Manual de Usuario


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del CROSSLEE G454ROYALBELM.LFE Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como archivo PDF después de que lo compre.

El Manual del Propietario (a veces llamado Manual del Usuario o Guía del Usuario) contiene información sobre cómo utilizar su dispositivo. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
,167$//$7,21 86,1* $ 

',$0(7(5 0(7$/ )/8( %2;

IMPORTANT: Restrictor plates must be removed. See Fig 15. When the metal flue box is to be built-in as a false chimney-breast using timber stud work with a plasterboard facing, the metal flue box should be enveloped with insulation material such as Rockwool or similar to prevent a build-up of heat within the structure. Either an air gap of 75mm should be maintained between any combustible materials and any part of the metal flue box or a minimum of 25mm of insulation material between the metal flue box and the combustible material. It is important that both the back panel and the appliance are sealed to the metal flue box to prevent any leakage of flue products or reduction in the flue draught. See Figs 4 & 5. 35(&$67 )/8( ,167$//$7,216 IMPORTANT: Restrictor Plates must be removed. See Fig 15. See Figs 6 � 8. &+(&.,1* &21',7,21 $1' &203$7,%,/,7< 2) 7+( &+,01(< Check that the chimney conforms to the required specifications as previously stated. Examine the condition and carry out any remedial work as necessary, if the flue has been used for solid fuel it should be swept and a smoke test carried out to check that satisfactory smoke clearance has been established. If all the smoke is not drawn into the flue, pre-heat the flue with a blowtorch or similar and re-check. If there is any uncertainty examine for the cause and if necessary seek expert advice. *$6 6833/< BEFORE COMMENCING WORK, TURN OFF ANY APPLIANCES THAT ARE FED BY THE METER AND ISOLATE THE GAS SUPPLY BY TURNING OFF AT THE METER The gas connection to this appliance is made with 8mm o/d rigid or semi rigid tube to a pressure test elbow situated on the L/H side of the burner as shown below. It is advisable to provide a means of isolating the gas supply to the appliance for servicing with either a restrictor elbow or isolation cock such as shown below. Provision is made in the rear L Hand corner of the outer casing to allow a gas supply to be fed to the burner assembly. A blanking plate and gasket is supplied with cutouts and slots that will enable a seal to be made around the supply pipe. If a restrictor elbow is to be used, it will be necessary to cut and form the bundy pipe supplied. Any pipe used under the burner must be in rigid tube such as Bundy, 3 pieces of Bundy are included in the fitting kit to assist the installer. (a) A short piece for use with a restrictor elbow. (b) A formed section for connection to an isolation cock, and (c) a formed section for R Hand supply using the inline connector supplied. The inlet pipe support bracket can be removed if necessary to gain greater access, by unscrewing the Control mounting lock nut and lifting over the spindle, as shown in Fig 9. Where a concealed gas supply is used, the installer is reminded of the requirements of BS 6891 1988 dealing with enclosed pipes. The Standard requires that when a gas pipe is fed through a wall, the pipe should be enclosed in a tight sleeve to protect against failure caused by movement and shall be constructed to prevent passage of gas either between the pipe and sleeve or sleeve and wall. Permanent sealant e.g. fire cement etc. should not be used as these would prevent removal of the firebox if so required.

Page 6

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.188 - Number of Queries: 129 - Query Time: 0.049